No, The etrailer Hitch Pin Alignment Collar # e98942 will does not work as an anti-rattle device. The Let's Go Aero # 63232 will work with The etrailer Hitch Pin Alignment Collar # e98942 (only for alligning the carrier) as long as your hitch mounted cargo tray has a hollow shank. The Aero anti rattle device pulls the shank against the inside wall of the hitch receiver using a spring block and tightened down bolt. This will not interfere at all with the etrailer collar. If you have a solid... view full answer...
The monitor that works with the Swift Hitch Wireless Hitch Alignment Camera - Night Vision - 4-Hour Camera Battery # SH01-C is # SH01R. view full answer...
If you are using the Kuat Transfer V2 Bike Rack for 1 Bike # KU64FR for a 2-inch hitch, I confirmed with Kuat that you will need the # HL1 because of the 1-1/4 adapter sleeve that comes with the rack. view full answer...
Roadmaster does have a base plate that will work, part # RM-521453-4. You'll also need the # RM-038 Duncan tow bar to Roadmaster Base Plate adapter. The reason we don't list the coupler style tow bars as being compatible is that the EZ4 type base plate drawbars need to be twisted 90° to remove, which isn't easy when the adapter is bolted on.
In other words, according to Roadmaster, it WILL work, it just won't be super-easy to remove the base plate draw bars as you'll need to unbolt the... view full answer...
The Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 does not have replacement pats such as a new wire harness. What that means is if your wire harness was somehow damaged or broken you would need to replace the unit with a new one. view full answer...
I can't really say that it's "better" to go with one over the other when it comes to using the Correct Track Trailer Alignment and Lift Kit - Single Axle # LC87120 over a Dexter Over/Under Conversion # K71-384-00 as they both will do the same basic job in different manners.
However, Correct Track Trailer Alignment and Lift Kit - Single Axle # LC87120 is what I recommend because it also works to keep your axles aligned properly to help ensure even tire wear and proper tracking behind the... view full answer...
For your 2003 Subaru Forester I recommend using the Curt # C12038, which is a Class II hitch with a 1-1/4" receiver; this Curt hitch will have a bit more durable powder coating than the others, so it's going to stand up to wear and tear a little better. There are only hitches with 1-1/4" receiver available for your Forester, so you will need a bike rack that has a 1-1/4" shank.
For the bike rack I recommend using the Thule Doubletrack Pro Platform-Style 2 Bike Rack for 1-1/4" and 2" Hitches... view full answer...
When installing The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4 inch # C11265 you will not have to remove the rear air dam it only has three installation steps. If present, remove existing bolts from tow loops. Then you would raise the hitch into position and align the holes in the side plates, secure the hitch with the hardware provided. Finally you torque down all hardware.
I will attach an installation video below. view full answer...
While we do not have a mirror like you're looking for we do still have another alternative for you.
Instead, take a look at the Swift Hitch Wireless Hitch Alignment Camera and Monitor # 04928.
This is a portable, wireless system that utilizes a magnet mount so you can position it anywhere, and also includes a handheld monitor with a 2-1/2", high resolution, full-color LCD screen.
With this system, you will have no issues hooking and unhooking your gooseneck trailer. view full answer...
The monitor that comes with the Hopkins Smart Hitch Backup Camera and Hitch Aligner System part # HM50002 has a mounting bracket with double sided tape that is designed to attach to your windshield, dashboard, or center console. In order to mount the monitor on your dash you will first want to clean the surface then remove the sticker and place it in the location you desire while holding down firly to secure it in place.
I spoke to my contact at Hopkins and they informed me that on an... view full answer...
I spoke with my contact at Hopkins and the license plate bracket/camera part of the Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 is not available as a replacement part. You will need to purchase a whole new system to replace the camera and license plate bracket parts. view full answer...
Sure, you can put a trailer hitch and tow with a 2005 Toyota Camry. You'll want to check your version of the owner's manual for capacities to ensure it aligns with what you are carrying, though; from my research it was 2,000 lbs but please do verify. In order to tow with your '05 Camry you'll just need the following parts:
- Curt Trailer Hitch Receiver # C12339
- 4-Flat Wiring Harness # C55308
- Drawbar # C45521
- Pin and Clip # F-4
- 2" Hitch Ball # C40018 or 1-7/8" Hitch Ball # C40001
The... view full answer...
The trailer hitch, wring, and ball mount are the main parts needed for towing a trailer so you're pretty much set unless the trailer is on the heavier end - then you'll need a brake controller and weight distribution hitch as well. Let me know if this is the case and I'll be happy to help you figure out the best parts for your setup!
Aside from that we do have the etrailer Bag Kit # e99039-9 which isn't a necessity, but it does include some locks, an alignment collar, and a storage bag... view full answer...
According to my research, the 2001 Chevy Tracker RWD w/ manual transmission is capable of being flat towed without modification, however it's not recommended to tow the vehicle above 55 mph.
Your motorhome would need a hitch and a trailer connector at the rear. For the vehicle, you'll need a tow bar, base plates, wiring so the vehicle taillights work along with those on the motorhome and a supplemental braking system.
The Blue Ox Alpha Tow Bar, part # BX7380 is an excellent choice for... view full answer...
When it comes to installing a trailer hitch on your 2013 Toyota Highlander The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2 inch # e98858 is 100% confirmed to fit your vehicle. The hitch will bolt right up with no problems.
The hitch has a bolt on installation with no welding required. The hitch has a matte black powder coat finish over a protective base coat that offers a superior rust resistance.
The Hopkins Plug-In Simple Vehicle Wiring Harness... view full answer...
In order to add a 2nd camera to the GCH Automotive Custom Third Brake Light Camera System - Night Vision - 7" Screen # 3460008 you'll need a camera that is has an RCA composite output. I spoke with our contact over at GCH Automotive and he recommended 2 different cameras depending on how you wanted them to be used.
The best option would seem to be the GCH License Plate Mounted Camera # 3460029 which will attach directly to your license plate mount and provide you a close up view of your... view full answer...
According to the owner's manual, a manual transmission equipped 2008 Toyota Yaris can indeed be flat towed behind a motorhome. To flat tow the vehicle, you'll need base plates, a tow bar, safety cables, a wiring harness, a supplemental braking system and possibly a high/low hitch adapter.
For base plates, I'd recommend the Roadmaster # 521181-1 and # RM-643 for safety cables. For a tow bar, we really like the Roadmaster Falcon All Terrain, part # RM-522. This particular tow bar features... view full answer...
The only cameras compatible with the Furrion # FOS05TASF would be the Furrion # FCN48TASF, which would need to be tapped into the reverse light circuit during installation to work in the manner you're seeking. We haven't tested this being installed on a passenger vehicle, but I don't see any reason it wouldn't work since all it requires is a power source. view full answer...
When installing The B&W Companion Slider Gooseneck-to-5th-Wheel Trailer Hitch Adapter # BWRVK3400 on your 2018 Ford F-250 with a 6-3/4 foot bed The Replacement Slider Base # BWRVB3405 installs into the ball hole of the B&W Turnoverball gooseneck hitch # BWGNRK1116-5W. If the turnoverball gooseneck hitch is already installed you will not have to drill any new holes into your truck bed.
The 5th wheel hitch has a gross towing weight up to 20,000 pounds and has a vertical load limit up to... view full answer...
To pair with your Blue Ox # BX1303 base plates I recommend using the etrailer SD Non-Binding Tow Bar for Blue Ox Base Plates - RV Mount - 2" Hitch - 6,000 lbs # e47ZR. This is a high quality non-binding tow bar at a great price point. The etrailer SD has telescoping and self aligning arms to allow for fast and easy hook up on any surface, so it's also easy to use. view full answer...
Go To Results